Відео

Hi Austin! To prep it for paint I did a quick wipe down with lacquer thinner to 'open' the finish and remove any oils. I then sprayed it.

She is still competing and doing quite well at it! Great hearing from you✌🏻

The Bump Stops have been on my Jeep for about 2.5 yrs. I have had no need to rebuild them as they have not leaked and have performed flawlessly. Good hearing from you✌🏻

Polices

Hey Rubi! With the 37's aired down it was getting bad, I couldn't turn unless I could roll a few feet, which is not always possible offroad. I was also overheating the P.S. fluid. With the Apex installed, I can now turn the wheel while aired down, no issues. It's so seamless, I sometimes forget I'm running it. Definitely recommend!

Hi✌🏻 They have been flawless. Good hearing from you!

Glad to help!

Here's the link for the Amp'd Throttle Booster. Be sure and order the correct device for your powertrain. www.holley.com/products/tuners_and_programmers/throttle_sensitivity_booster/parts/48868-JL2

I have a JL Wrangler on 37" Nitto Ridge Grapplers and running 4.88 gears. This combo got me very close to the stock set-up and works perfectly. You must be really feeling the 37 and 3.73. My JL is a Rubicon, so I was starting with 4:10 gears.

I am upgrading to 4.88 and a possi unit in rear .

Actually, I want you to consider another device. Check out my video on the Superships Amp'd 2.o Throttle booster. It's my favorite!

Hi Humberto! I spoke with Holley/Superchips about this very topic a couple of weeks back and was told they do not currently offer tuning for the 2024. I just inquired again asking if a 2024 tune is in development. I'll let you know what I hear back.

Hi again, I got a quick reply back from the tech(s) at Holley. Flashcal products and support for the 2024 are available. The tune is in the works. No ETA available yet. For 2024, Jeep is using a new ECM type and Holley/Superchips is working on it. Hopes this helps.

Well said! Great hearing from you✌🏻

Good evening! So good hearing from you and great to hear your comments.

Hey Zach, great hearing from you! You going to love the 3.3's/MC long arm/Fox 2.0 Bumpstops. The Bumpstops have performed perfectly, definitely recommend them.

Hi and good hearing from you! I assume you are asking about the winch mount plate? That is from Artec Industries.

Sorry i mean the license plate mount

@@elviejito401 Ahh, ok. The license plate mount is from Maximus-3. Here's a lnk: maximus-3.com/home/jl-jt-stealth-front-license-plate-bracket-frame

Thank you, really appreciate the compliment. Yes, I would love to discuss doing a product review on your portable Jump Starter. Please reach out to me via email. Talk soon.

@@ExpeditionBuilds Just did it, Look forward to hearing from you

Hi David. Did this just start? Any other symptoms? Let me know if you can provide more info. I can reach out to RSE. Have you spoken with RSE about this?

No it’s all the symptoms. Been doing it ever since I got them installed. Went to the shop and said I gotta keep battery on charge if I ever leave it that long. I emailed them… got no response from RSE

Has it now I pulled out the fuse from the steps.

@@davidbautista9679 Ok, I'm going to reach out to them and see if we can get you some help on this. A little more info would help. Are these Gen 2, Gen 3? What Jeep are they on, JK or JL? How long have they been on your Jeep?

@@ExpeditionBuilds GEN 3 on a JKU 9 months.

Hi, and good hearing from you. I intentionally left specifics out of the video, things like how much toe in or toe out as rigs are set up differently. I thought one could see how to use it pretty well from the video I presented.

Thank you! Great hearing from you.

Hi, great hearing from you! That can definitely happen. I do love how the raised areas keep your feet above the wet/mess.

Thanks, great hearing from you!

❤🙏🏼

Thank You!!!

Apologies for not getting back to you sooner, we've been out shooting content. Agree, those cooler screws are tough. That shouldn't be an issue leaving the sandwich plate on. Do you feel you want to reach out to Apex for verification on this?

@@ExpeditionBuilds No worries you replied within a day that is actually pretty fast. The instruction manual says to remove the sandwich plate and install the HP line by itself, but why is there a need to trim the mounting bracket if that's the case? I think they are contradicting themselves here. I am just gonns leave it as it is.

@@ghernandez6457 Sorry I don't have an answer as to why the instructions ask for the sandwich plate removal? If you feel good about your install, roll with it.

Thank you for your comment and we truly appreciate your support🙏🏼

@@ExpeditionBuilds God Bless You

Wow, what a great compliment! Really appreciate hearing from you.We continue to push ourselves to keep putting out high level content.

@@ExpeditionBuilds Hopefully the next one will be even better than this one.

@@DankBruv We'll give it our best. Be well!

Hi, and great hearing from you! I am running the Rugged Ridge Fender chop kit. I chose this kit because it allows me to keep the inner fender liners as well as the black edge trim. Also look at the new fender chop light from American Adventure Labs. Let me know if you have trouble locating those, I may be able to help.

@@ExpeditionBuilds thank you so much for the response. I’ll look it up, if I have issues finding it, I’ll let u know. Thanks for the help.

Hi Daniel, great hearing from you! Let me see if we can make the thumbnail more inviting. Really appreciate the feedback.

Hi, updated the thumbnail. Thoughts?

Wow, thank you!

Hi Mark! Yes, they should fit your Extreme Recon. Good hearing from you✌🏻

@@ExpeditionBuilds which ones do I need for the rear, your video showed you drilling the rivets but no install. ✌🏻

Hello!

Hi. The tuner cost is ~ $540.00. A couple of ways to do this. Follow the instructions on the Superchips website. - Send your PCM to them to be unlocked. They send it back with the new tune. - Buy a new PCM (with tune) and keep you stock PCM (+$600.00) Let me know if you have any additional questions, glad to help.

Hey Brandon, good hearing from you! Yes, performing perfectly. I can recommend this mod👍🏻

@@ExpeditionBuilds This still work for the 2024 model? I thought I heard somewhere that these no longer work for some of newer models, but I may have dreamt that. Haha Great video btw!

@@bcraftmath I'm not sure about whether or not this tune works on the 2024? I plan on checking in with Superchips next week and I'll ask about the status for the 2024. Thanks for the compliment on the video✌🏻

@@ExpeditionBuildsI'd appreciate that! I don't see a flashpaq fire my 24 4xe 2.0, but man of love something like this to get a lil more umph from the bottom.

@@bcraftmath I'll let you know what I hear.

Hi Chris! I just added the link(s) in the description. Good hearing from you.

Thanks brother!

Hi, we will occasionally sell a vehicle if we are upgrading or starting a new build. Maybe check Autotrader.

Good night! Great hearing from you.

❤❤🎉❤😅😊😊😅😊😅

That doesn't surprise me at all🌞

😆 so very true!